ACV HeatMaster 201 Booster User's Guide

excellence in hot waterInstallation, Operating andServicing InstructionsHeatMaster®HeatMaster®20108/2006 - 66402500.C

8BOILER ROOMImportant• Keep vents free at all times.• Do not store inflammable products in the boiler room.• Do not store corrosive products near th

9INSTALLATIONHOT WATER CONNECTIONSPressure reducing valveIf the mains water pressure is greater than 6 bar, a pressure reducingvalve must be fitted.Ex

10ELECTRICAL CONNECTIONSElectrical supplyThe boiler operates on a single-phase supply of 230V/50Hz. Youshould install a control box with a double-pole

11INSTALLATIONHeatMaster®201 wiringB. BlueBr. BrownBk. BlackOr. OrangeG. GreyR. RedW. WhiteY. Ye l l o wV. Violet5MCBA t2 x 2 fils14 x 0,25mm2010203AM

12COMMISSIONINGFILLING THE HOT WATER AND HEATING CIRCUITSIMPORTANTHot water tank must be pressurised before the heatingcircuit is filled.1. Close the

BE FR AT DK ES UK IT PT IE SE NL LU DEI 2Er XI 2E(R)B xI 2H XXXXXXXXI 3P XX XX XXI 2L XI 2ELL XI 2E X13BURNER FEATURES201 gas burner characteristicsGa

14Draining the boiler’s primary circuit 1. Put the main switch on the control panel to OFF, cut the outsidepower supply and close the gas-supply valve

15MCBA FOR SPECIALISTS: INSTALLER, SERVICE ENGINEERPILOT MODEPilot modeAfter you power down the appliance the screen displays Pilot mode,as shown in t

16MCBA FOR SPECIALISTS: INSTALLER, SERVICE ENGINEERSAFETY STOP (ERROR MODE)If a fault occurs while the appliance is running, the system locks andthe s

17MCBA FOR SPECIALISTS: INSTALLER, SERVICE ENGINEERSETTING THE PARAMETERSParameter modeTo access Parameter mode when the system is in Pilot mode, pres

18MCBA FOR SPECIALISTS: INSTALLER, SERVICE ENGINEERNight-time heating temperature reduction (°C)STEPFan speed in heating mode (rpm x 100)STEP1052Key D

19MCBA FOR SPECIALISTS: INSTALLER, SERVICE ENGINEERHeating lock time (sec x 10.2)STEPHot water lock time (sec x 10.2)STEPLock time to switch from hot

20MCBA FOR SPECIALISTS: INSTALLER, SERVICE ENGINEERINFORMATION ON THE INSTALLATIONInfo modeTo switch from Pilot mode to Info mode, press “Mode” twice.

21MCBA FOR SPECIALISTS: INSTALLER, SERVICE ENGINEERCOMMUNICATION MODE (WITH CODE)When in this mode, the system displays the communication betweenthe b

22SPARE PARTSNo. Jackets Codes HeatMaster®201A01 Right side 21471415A02 Left side 21471415A03 Right side rear corner 21478415A04 Left side rear corner

23SERVICE RECORDService date:% CO2(min. load):% CO2(max. load):GasPropaneModel:Serial number:Heating system pressure setting:❏❏Name and signature:Flue

24SERVICE RECORDService date:% CO2(min. load):% CO2(max. load):GasPropaneComments:❏❏Name and signature:Flue gas T°:Efficiency:Gas pressure:Service dat

INTERNATIONALACV international n.vKERKPLEIN, 39B-1601 RUISBROEK - BELGIUMTEL.: +32 2 334 82 20FAX: +32 2 378 16 49E-MAIL: international.info@acv-world

1INDEX INTRODUCTIONINTRODUCTION 1Target group 1Symbols 1Certification 1General information and safety instructions 2USER GUIDE 2Using the boiler 2Sett

2INTRODUCTIONGENERAL INFORMATION AND SAFETY INSTRUCTIONSIF YOU SMELL GAS:- Immediately shut off the gas supply.- Ventilate the boiler room.- Do not us

3USER GUIDEReset1Status T°1 X1 XModeStep2 XModeStore1 XStore1 XStandbymodeStand by modeSETTING THE PARAMETERSSetting the temperature of the hot water:

OPERATING PRINCIPLEThe HeatMaster®is a high performance, direct fired hot waterstorage heater, which has indirect heat transfer due to its Tank-in-Ta

5DESCRIPTIONThermostat-pressure gauge bulbFlange of the burner chamber plateSteam trapT&P valve (optional)Hot water outletChimney reducerNTC 3 sen

6EFFECTIVE DIMENSIONSThe appliances delivered are factory-tested. Upon receipt, remove the packing and check that there is no damage to the appliances

7TECHNICAL SPECIFICATIONMAXIMUM OPERATING CONDITIONSMaximum service pressure (tank full of water)- Primary circuit: 3 bar- Secondary circuit: 10 barTe